Skip to content

(Archived) EFI for ASRock-Z390M-Pro4-i7-9700K-Sapphire-RX580 Hackintosh

Notifications You must be signed in to change notification settings

sarkrui/Z390M-Pro4-i7-9700K-Hackintosh

Repository files navigation

Z390MPro4-i7-9700K-Sapphire-RX580

Introduction

This repository is designed for Asrock Z390MPro4 to run Mojave 10.14.X/Catalina 10.15.X with no hassle. However, due to the time constraint, a step by step installation guide won't be covered in this guide. For more information (regarding installation), please check [Guide] Creating OSX Installer by Rehabman or installing Mojave 10.14.x with Etcher.

Specs

  • Asrocks Z390M Pro4 (M.2 Key B * 2 + M.2 Key A+E * 1 + PCIe 3.0 x16 * 2)
  • Intel i7-9700K (4.9GHz GHz OC, SMBIOS iMac19,1)
  • Clover Bootloader (r5070) / OpenCore (0.5.3)
  • Be quiet! Dark Rock Pro 4 (250w TDP, highly recommended)
  • Kingston HyperX Fury Black 16GB 3200MHz DDR4 8G * 2 (3200MHz OC)
  • WD Black 2018/PC SN720 NVMe 1T SSD
  • Sapphire RX 580 Nitro+ 8G (BruceX 5K Apple Res 422 Master Exporting time 13s)
  • Apple BCM94360CD Wi-Fi/Bluetooth + M.2 NGFF Key A+E Adapter

Performance

image-20191005011344996

System Brief

USBs Mapping

(Since I do not have any front USB, only the rear ones were enabled.)

What works

  • dGPU Hardware Accelaration (Final Cut Pro X, VideoProc, Compressor tested)
  • AirDrop, Handoff (Apple Wi-Fi/Bluetooth required)
  • iMessage (complete serial required)
  • All USB3.1 Gen1/USB2.0 ports (few USB2.0 ports disabled)
  • HDMI Audio (Sound Control is required to adjust volume)
  • Onboard HD Audio (Realtek alc892, layout id: 1)

Bugs

  • USB 3.1 Gen2 (may require a USB3.1 Gen2 to PCIe Card, i.g. ASM1142 chip-based)
  • USB Type-C has no video output (iGPU video output has been disabled to enable dGPU HW acceleration)

BIOS Settings

  • BIOS Version P1.3 (Please do not upgrade! I was NOT able to boot up macOS with P4.X BIOSs and I had to disassemble the chip and flash P1.30 firmware.)

We don't recommend users to update the BIOS if their system is already running normally.

  1. Download Hackintosh-BIOS.BIN from the release page or Clone the whole repository (the file is under /BIOS_settings) and place it in an FAT32 USB.
  2. Enter BIOS setup
  3. direct to OC Tweaker/ Load USER UEFI Setup Profile from Disk
  4. select Hackintosh-BIOS.BIN from your USB.

Installation

Option 1: GUI (recommended)

Option 2: Command-line

Changelog

2019/11/29

  • Add OpenCore Bootloader support
  • NVRAM tested (motherboard CFG clock disabled)
  • Remove WhateverGreen for 1.2GHz iGPU clock speed
  • Upate kexts, BIOS settings
  • Replace BCM94331CD with BCM94360CD for better AirDrop/Handoff support

2019/11/01

  • Update kexts/driver
  • Catalina 10.15.1 compatiable

2019/10/05

  • Fixed onbard HD audio output

2019/10/05

  • Initial release