Skip to content
forked from kirovilya/CCLib

An arduino library that implements the CC.Debugger protocol of TI

License

Notifications You must be signed in to change notification settings

s-hadinger/CCLib

 
 

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

This fork from CCLib is meant to simplify the flashing of CC2530 devices with a Wemos D1 Mini or any equivalent based on ESP8266, to be used with Tasmota.

It is based on this fork from kirovilya and instructions described in this blog post.

The port speed is reduced to 19200 to avoid communication errors :ERROR: Could not read from the serial port!

Default pinout is the following:

  • GPIO4 connected to CC_DC aka P2_2 or Debug Clock
  • GPIO5 connected to CC_RST
  • GPIO12connected to CC_DD aka P2_1 or Debug Data

Tasmota Zigbee currenlty only supports ZNP 1.2 default mode for coordinator. CCLib requires to remove the second last line.

For convenience, ready to use firmwares are provided, just unzip them and select the right one: CC2530, CC2530 + CC2591 or CC2530 + CC2592.

Make sure you have Python 2.7 installed and install pyserial 3.0.1: pip install pyserial==3.0.1

Before flashing, check the connectivity:

python Python/cc_info.py -p <serial_port>

Example or result:

INFO: Found a CC2530 chip on /dev/cu.usbserial-xxxx

Chip information:
      Chip ID : 0xa524
   Flash size : 16 Kb
    Page size : 2 Kb
    SRAM size : 1 Kb
          USB : No

Device information:
 IEEE Address : 000000000000
           PC : 0000

Debug status:
 [ ] CHIP_ERASE_BUSY
 [ ] PCON_IDLE
 [X] CPU_HALTED
 [ ] PM_ACTIVE
 [ ] HALT_STATUS
 [X] DEBUG_LOCKED
 [X] OSCILLATOR_STABLE
 [ ] STACK_OVERFLOW

Debug config:
 [ ] SOFT_POWER_MODE
 [ ] TIMERS_OFF
 [ ] DMA_PAUSE
 [ ] TIMER_SUSPEND

To flash the firmware, use the following command: (flashing takes ~1 hours)

python Python/cc_write_flash.py -e -p /dev/cu.usbserial-1420 -i Bin/CC2530_DEFAULT_20190608_CC2530ZNP-Prod.hex

INFO: Found a CC2530 chip on /dev/cu.usbserial-xxxx

Chip information:
      Chip ID : 0xa524
   Flash size : 256 Kb
    Page size : 2 Kb
    SRAM size : 8 Kb
          USB : No
Sections in Bin/CC2530_DEFAULT_20190608_CC2530ZNP-Prod.hex:

 Addr.    Size
-------- -------------
 0x0000   8176 B
 0x1ff6   10 B
 0x3fff0   1 B
 0x2000   239616 B

This is going to ERASE and REPROGRAM the chip. Are you sure? <y/N>:  y

Flashing:
 - Chip erase...
 - Flashing 4 memory blocks...
 -> 0x0000 : 8176 bytes
    Progress 100%... OK
 -> 0x1ff6 : 10 bytes
    Progress 100%... OK
 -> 0x3fff0 : 1 bytes
    Progress 100%... OK
 -> 0x2000 : 239616 bytes
    Progress 100%... OK

Completed

Once flashed, the recommended connection to Wemos D1 mini is:

  • GPIO13 (Zigbee RX) connected to CC_TXD aka P0_3
  • GPIO15 (Zigbee TX) connected to CC_RXD aka P0_2


CCLib

Build Status (Travis) Build Status (AppVeyor) Join the chat at https://gitter.im/Arduino-CCLib

A set of utilities to convert your Arduino board to a CC.Debugger for flashing Texas Instruments' CCxxxx chips. It currently supports the CC2530/40/41 chips (compatibility table) but with your help it can support any chip compatible with the CC.Debugger protocol.

Keep in mind but this more than just a set of utilities! It comes with complete, reusable Arduino and Python libraries for adding CC.Debugger support to your projects!

Usage

If you are just in hurry to flash your CCxxxx chip, follow this guide, however you should first check the compatibility table later in this document!

1. Prepare your arduino board

  1. Install the Arduino/CCLib library to your arduino IDE
  2. Load the CCLib_proxy example and change the the LED, CC_RST, CC_DC, CC_DD_I and CC_DD_O constants to match your configuration.
  3. Flash it to your Teensy/Arduino
  4. We are going to need a voltage divider from 5V (arduino) to 3.3V (CCxxxx chip), therefore you will need to wire your arduino according to the following diagram:
For the DD Pin:

 <CC_DD_O> --[ 100k ]-- <CC_DD_I> --[ 200k ]-- <GND>
                            |
                           {DD}

For the DC Pin:

 <CC_DC> --[ 100k ]-- {DC} --[ 200k ]-- <GND>

For the RST Pin:

 <CC_RST> --[ 100k ]-- {RST} --[ 200k ]-- <GND>

Where {DD}, {DC} and {RST} are the pins on the CCxxxx chip and <CC_DD_O>, <CC_DD_I>, <CC_DC>, <CC_RST> are the pins in your ardiuno board.

In an arduino/breadboard set-up, this looks like this:

2. Prepare your software

  1. You will need Python 2.7 or later installed to your system
  2. Open a terminal and change directory into the Python folder of this project
  3. Install required python modules by typing: pip install -r requirements.txt
  4. Test your set-up:
~$ ./cc_info.py -p [serial port]

If you see something like this, you are ready:

Chip information:
      Chip ID : 0x4113
   Flash size : 16 Kb
    SRAM size : 1 Kb
          USB : No

Device information:
 IEEE Address : 13fe41b61cde
           PC : 002f

However, if you see something like this, something is wrong and you should probably check your wiring and/or reset the arduino board or the CC board.

Chip information:
      Chip ID : 0x4113
   Flash size : 16 Kb
    SRAM size : 1 Kb
          USB : No

Device information:
 IEEE Address : 000000000000
           PC : 0000

3. Using the software

The python utilities provide a straightforward interface for reading/writing to your CCxxxx chip:

  • cc_info.py : Read generic information from your CCxxxx chip. Usage exampe:
~$ ./cc_info.py -p /dev/ttyS0
  • cc_read_flash.py : Read the flash memory and write it to a hex/bin file. Usage example:
~$ ./cc_read_flash.py -p /dev/ttyS0 --out=output.hex
  • cc_write_flash.py : Write a hex/bin file to the flash memory. You can optionally specify the --erase parameter to firt perform a full chip-erase. Usage example:
~$ ./cc_write_flash.py -p /dev/ttyS0 --in=output.hex --erase
  • cc_resume.py : Exit from debug mode and resume chip operations. Usage example:
~$ ./cc_resume.py -p /dev/ttyS0

NOTE: If you don't want to use the --port parameter with every command you can define the CC_SERIAL environment variable, pointing to the serial port you are using:

~$ export CC_SERIAL=/dev/ttyS0

Compatibility Table

In order to flash a CCxxxx chip there is a need to invoke CPU instructions, which makes the process cpu-dependant. This means that this code cannot be reused off-the-shelf for other CCxxxx chips. The following table lists the chips reported to work (or could work) with this library:

Chip Chip ID Driver Status
CC2530 0xa5.. CC254X ✅ Works
CC2531 0xb5.. CC254X 🔶 Looking for testers
CC2533 0x95.. CC254X 🔶 Looking for testers
CC2540 0x8d.. CC254X ✅ Works
CC2541 0x41.. CC254X 🔶 Looking for testers
CS2510 0x81.. CS2510 🔶 Looking for testers

Contributing other chip drivers

Since the arduino sketch is quite simple, it's possible to support any CCxxxx device solely by creating a new chip driver. Even if your chip uses a different debug protocol instruction set (such as CC2510) you can modify it on-the-fly.

In order to create a new chip driver you should create a new file in the Python/cclib/chip folder with the name of your chip (for example cc2510.py), and create a new Python class, subclassing from the ChipDriver class. For example:

class CC2510(ChipDriver):
    """
    Chip-specific code for CC2510 SOC
    """

    @staticmethod
    def test(chipID):
        """
        Check if this ChipID can be handled by this class
        """
        return ((self.chipID & 0xff00) == 0x8100)

    def chipName(self):
        """
        Return Chip Name
        """
        return "CC2510"

    def initialize(self):
        """
        Initialize chip driver
        """

        # Get chip info
        self.chipInfo = self.getChipInfo()

        # Populate variables
        self.flashSize = self.chipInfo['flash'] * 1024
        self.flashPageSize = 0x400
        self.sramSize = self.chipInfo['sram'] * 1024
        self.bulkBlockSize = 0x800
        self.flashWordSize = 2

And you must then register your class in the Python/cclib/ccdebugger.py

# Chip drivers the CCDebugger will test for
from cclib.chip.cc2540x import CC254X
from cclib.chip.cc2510 import CC2510
CHIP_DRIVERS = [ CC254X, CC2510 ]

After that you need to implement all the functions exposed by the ChipDriver (available in Python/cclib/chip/__init__.py), but you can just copy the cc2540x.py driver and work on top of it.

We are looking forward for your support for new chips!

Protocol

The protocol used between your computer and your Arduino is quite simple and not really fault-proof. This was intended as a pure proxy mechanism in order to experiment with the CC Debugging protocol from the computer. Therefore, if you interrupt any operation in the middle, you will most probably have to unplug and re-plug your Teensy/Arduino. That said, here is the protocol:

Since most of the debug commands are at max 4-bytes long, we are sending from the computer a constant-sized frame of 4-bytes:

+-----------+-----------+-----------+-----------+
|  Command  |   Data 0  |   Data 1  |   Data 2  |
+-----------+-----------+-----------+-----------+

The only exceptions are:

  • The brust-write command (CMD_BRUSTWR), where up to 2048 bytes might follow the 4-byte frame, and
  • The instrunctionset update command (CMD_INSTR_UPD), were 16 bytes must follow the 4-byte frame.

The Teensy/Arduino will always reply with the following 3-byte long frame:

+-----------+-----------+-----------+
|   Status  |    ResH   |  Err/ResL |
+-----------+-----------+-----------+

If the status code is ANS_OK(1), the ResH:ResL word contains the resulting word (or byte) of the command. If it's ANS_ERR(2), the ResL byte contains the error code.

Disclaimer

Users have successfully flashed various BlueGiga BLE112/BLE113 (CC2540) modules with this solution, however the developers DO NOT GUARANTEE THAT THIS WILL WORK IN YOUR CASE! The developers cannot be held liable for any damage caused by using this library, directly or indirectly. YOU ARE USING THIS CODE SOLELY AT YOUR OWN RISK!

License

Copyright (c) 2014-2016 Ioannis Charalampidis

This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program. If not, see http://www.gnu.org/licenses/.

About

An arduino library that implements the CC.Debugger protocol of TI

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages

  • Python 72.0%
  • C++ 26.7%
  • Other 1.3%