Skip to content

A multi-platform C++ framework used to drive Dynamixel and HerkuleX smart actuators, and its control GUI.

License

Notifications You must be signed in to change notification settings

emericg/SmartServoFramework

Repository files navigation

SmartServoFramework 0.100

Build Status Build status License: LGPL v3

SERVO

Introduction

SmartServoFramework is a C++ multi-platform framework used to drive "smart servo" devices like Dynamixel or HerkuleX actuators. It has been developed at Inria Grenoble research center.

Linux (and most Unix systems), macOS and Windows operating systems are supported. All you need to begin moving stuff around is at least one servo, a serial port adapter and a modern C++ compiler! SmartServoFramework works well on Raspberry Pi or other embedded boards, but will not work on Arduinos nor any other microcontrollers.

Dynamixel devices from Robotis and HerkuleX devices from Dongbu Robot are high-performance networked actuators for robots available in wide range of sizes and strengths.
They have adjustable torque, speed, angle limits, and provide various feedback like position, load, voltage and temperature...

This framework can be used with any Dynamixel or HerkuleX devices. We support all models of HerkuleX from the DRS-0101 up to the DRS-0602. For Dynamixel that means AX, EX, MX, XL-320, X series, as well as the older RX and DX series. We even have support for the AX-S1 and IR sensor array! Please note that the Dynamixel PRO devices should work (the version 2 of the communication protocol is implemented, and works great with X serie), but they are considered as experimental since we couldn't test with any real device.
Support for other devices, brands or protocols may be added in the futur...

We provide two different APIs:

  • Simple API: Use this API to easily get/set values to your servos by sending simple synchronous instructions, then waiting for the answers!
  • Managed API: Setup a controller and attach servo instances to it. Manipulate servo objects and let the controller synchronize its "virtual" register values with the real servo hardware in a background thread with a fixed frequency. Beware: this API is more complex to master, and not entirely stable ;-)

Documentation

More informations on how to use the framework and your devices are available inside the documentation/ directory, and mirrored on the wiki. Please check these docs ;-)

You can dynamically generate a full API documentation from the source code using Doxygen. This will prove very important in order to work efficiently with the framework. The documentation will be accessible through documentation/APIs_documentation.html.

If you are running a macOS/Linux system you can easily generate the documentation from a terminal:

$ cd SmartServoFramework/
$ doxygen Doxyfile

If you have problems with the command line, it's just as easy to generate the documentation using DoxyWizard, Doxygen's GUI.

Building the framework

A full documentation is available in the documentation/BuildInstructions.md

Dependencies

You will need a modern C++11 capable compiler:

  • GCC >= 5.1
  • LLVM >= 4.0
  • MSVC >= 2015

Build system:

  • CMake (ONLY needed to build the standalone library)
  • Scons (ONLY needed to build the examples)
  • Doxygen (ONLY needed to generate the documentation)

Building SmartServoFramework library

$ cd SmartServoFramework/build/
$ cmake ..
$ make

Building test softwares

Various test softwares are available in the examples/ directory for you to play with:

  • ex_simple: Control up to four servos with your keyboard using the 'Simple API'.
  • ex_simple_threaded: ex_simple variant, with servos actions and keyboard handled in two separate threads.
  • ex_controller: Control four servos with your keyboard using the 'Managed API'.
  • ex_sinus_control: Control a servo with sinusoid curve for both speed and position. Enable OpenCV to get a nice position/speed graph.
  • ex_advance_scanner: Scan serial ports for Dynamixel servos, for all IDs and all (but configurable) serial port speeds.

You can build them all at once:

$ cd SmartServoFramework/examples/
$ scons

Serial communication

A full documentation is available in the documentation/SerialCommunication.md

This framework can be used with any combination of RS-232 ports, USB to TTL adapters, USB to RS-485 adapters, half or full duplex... But you'll need the right link for the right device.

One more important thing: you need to power your servos with proper power supply. Shaky power sources have been known to cause interferences on serial bus, resulting in numerous packet corruptions. Be careful when using batteries and power converters!

First you will need to make sure your software can access your serial port:

  • If you are running Linux, you may need special permissions from the uucp and/or dialout groups in order to access serial ports. You can add your user account to these groups with this command: # usermod -a -G uucp,dialout $USER (you'll need root credentials for this operation).
  • If you are running macOS, depending on your adapter, you may need to install the FTDI driver, or the CP210x driver.
  • If you are running Windows, you may need to install the FTDI driver for the USB2Dynamixel device. You may also need other drivers depending on your adapter (like the USB2AX driver, the CP210x driver, or the official FTDI driver).

Communication with Dynamixel devices

Note: Regular "full-duplex" TTL converters will NOT work with "half-duplex TTL" Dynamixel servos (AX serie, MX-T serie, XL and X*-T serie, ...).

  • USB2AX: Unofficial but awesome device designed to manage TTL communication with your Dynamixels (AX serie, MX-T serie, X serie, ...).
  • USB2Dynamixel: Official device that can manage all Dynamixel devices through RS232 / RS485 / TTL communications.
  • Home made TTL half-duplex device: like this setup from Savage Electronics (in spanish), or this one from memememe (in english).

Communication with HerkuleX devices

You need a serial port with a regular "full-duplex" TTL converter to use HerkuleX devices.

SmartServoGui

SmartServoGui has its own README in the SmartServoGui/ directory, where you can learn more about its features!

SmartServoGui is a fully featured Qt GUI application that helps you discover devices on available serial links, get an overview of all of their registers, and easily tweak their settings! Like the framework, it is fully multi-platform.

Quick installation

$ cd SmartServoFramework/SmartServoGui/
$ qmake-qt
$ make

Screenshots!

GUI2

GUI3

Get involved!

Developers

You can browse the code on the GitHub page, submit patches and pull requests! Your help would be greatly appreciated ;-)

Users

You can help us find and report bugs, propose new features, help with the documentation and more! Visit the Issues section of the GitHub page to start!

License

SmartServoFramework is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 3 of the License, or (at your option) any later version.
Read the LICENSE file or consult the license on the FSF website directly.

Copyright (c) 2014, INRIA, All rights reserved.
Emeric Grange [email protected]
Dominique Vaufreydaz [email protected]