Skip to content

ESP32-Musings/OTA_update_STM32_using_ESP32

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

11 Commits
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

Stargazers Forks Issues License


Logo

OTA for STM32Fxx MCU using ESP32

Program your STM32Fxx Over-the-Air using ESP32
****
View Code · Report Bug · Request Feature · Create a Pull Request

Table of Contents

About the Project

The project aims at enabling firmware update of STM32Fxx and STM32Gxx series MCUs Over-the-Air using ESP32.

Testing was done with ESP32-DevKitC v4 board and STM32F103C8T6 (Blue Pill), STM32F072C8T6 and STM32G431KB (NUCLEO-G431KB). You can try with any other STM32Fxx/STM32Gxx MCUs and let us know how it worked out.

Code

/esp_stm_flash -> Basic flashing utility, requires path of the .bin file which has been already uploaded in SPIFFS

/file_serving_stm -> OTA demo, with HTTP File Server with embedded flash link

/references -> Python scripts for understanding the flashing protocol commands and verification

Getting Started

Hardware Required

To run the OTA demo, you need an ESP32 dev board (e.g. ESP32-WROVER Kit) or ESP32 core board (e.g. ESP32-DevKitC). For the STM32, you can use the STM32 Blue Pill.

Prerequisites

  • ESP-IDF v4.0 and above

    You can visit the ESP-IDF Programmming Guide for the installation steps.

  • Arduino IDE

    Arduino IDE provides with an easy way to generate the .bin files for your STM32 MCU. For setting up Arduino Core for the STM32 family, you can follow this link.

    You can also use CubeIDE or Keil for generation of .bin files.

Setting Up

  1. Wire your STM32 (e.g. Blue Pill) to the ESP32 as follows:

    ESP32 STM32
    GPIO4(TX) PA10(RX)
    GPIO5(RX) PA9(TX)
    GPIO19 RESET
    GND GND
  2. Generate a .bin file for the STM32 MCU code you want to flash.

Disclaimer

We have assumed that the STM32 is already in boot mode before flashing the code (Step 1 & 5 in Usage section). You can use a MOSFET as a switch to automate the process, using an ESP32 GPIO as an input.

The program code uses only the path of the binary file to be flashed as a parameter. Thus, it can be easily integrated into any other projects as the file can be sent to ESP32 over any protocol (MQTT, HTTP Client, WebSockets).

Read carefully the Boot Mode Procedure (AN2606) and the USART protocol used in Bootloader Mode (AN3105) in order to deeply understand how to use this project with other STM32 microcontrollers.

Usage (For STM32 Blue Pill)

  1. Make sure the BOOT0 jumper pin on the board is set to 1 (programming mode) while uploading the code. Once the code is flashed this pin can be changed back to initial position (operating mode). This procedure with your STM32Fxx MCU varies according with your MCU version.

    Refer this documentation for help.

  1. Open the project configuration menu (idf.py menuconfig) go to Example Connection Configuration ->
    1. WiFi SSID: WiFi network to which your PC is also connected to.
    2. WiFi Password: WiFi password

  1. In order to test the OTA demo -> /file_serving_stm :
    1. Compile and burn the firmware idf.py -p PORT -b BAUD flash
    2. Run idf.py -p PORT monitor and note down the IP assigned to your ESP module. The default port is 80.
    3. Test the example interactively on a web browser (assuming IP is 192.168.43.82):
      • Open path http://192.168.43.82/ to see an HTML web page with list of files on the server (initially empty)
      • Use the file upload form on the webpage to select and upload a .bin file to the server
      • Click a file link to download / open the file on browser (if supported)
      • Click the delete link visible next to each file entry to delete them
      • Click on the flash link to flash the .bin code file uploaded to the connected STM32.

  1. After clicking the flash link, you should get the following results -

  1. Revert the BOOT0 pin to its initial position and press the RESET Button on the STM32.
  2. Voila! your STM32 is now running the code you uploaded Over-the-Air!

Compatibility

According to STM documentation, this project could be compatible with a wide range of microcontrollers, prior to some customization:

  • STM32F0 Series (verified)
  • STM32F1 Series (verified)
  • STM32F2 Series
  • STM32F3 Series
  • STM32F4 Series
  • STM32F7 Series
  • STM32G0 Series
  • STM32G4 Series (verified)
  • STM32H7 Series
  • STM32L0 Series
  • STM32L1 Series
  • STM32L4 Series
  • STM32L5 Series
  • STM32U5 Series
  • STM32WB Series
  • STM32WL Series

Troubleshooting

  • Check your wiring. Make sure that the ESP32 and STM32 are powered separately. Don't power one MCU using the other.
  • Verify your WiFi SSID and password.
  • Check if your STM32 is locked using this official tool by STMicroelectronics and unlock it by erasing the memory of your chip.
  • Check your STM32 code, which generated the .bin file, for any 'logical' errors.
  • For any other bugs or errors, you can always raise issues.

Contributors

For OTA updates for AVR MCUs, you can follow this project.

Acknowledgements and Resources

License

Distributed under the MIT License. See LICENSE for more information.