Does this support zigbee subdevice control

[NJPYY]

Does this support zigbee subdevice control

[xZetsubou]

3.0.01b beta should should support sub-devices,

However if you want to test this integration without losing your settings.
An easy way take a quick backup for your config folder.
test the integration then you can go back to your old folder.

I would also be glad in-case you tested it to give me the name if your tested device.

[NJPYY]

yes

2023-08-30 05:31:33.367 DEBUG (MainThread) [homeassistant.core] Bus:Handling <Event state_changed[L]: entity_id=sensor.kai_guan_1, old_state=<state sensor.kai_guan_1=1; raw_state=1, device_class=enum, friendly_name=switch1 @ 2023-08-30T13:31:24.289860+08:00>, new_state=<state sensor.kai_guan_1=0; raw_state=0, device_class=enum, friendly_name=switch1 @ 2023-08-30T13:31:33.367755+08:00>> 2023-08-30 05:31:33.368 DEBUG (Recorder) [homeassistant.components.recorder.core] Processing task: EventTask(event=<Event state_changed[L]: entity_id=sensor.kai_guan_1, old_state=<state sensor.kai_guan_1=1; raw_state=1, device_class=enum, friendly_name=switch1 @ 2023-08-30T13:31:24.289860+08:00>, new_state=<state sensor.kai_guan_1=0; raw_state=0, device_class=enum, friendly_name=switch1 @ 2023-08-30T13:31:33.367755+08:00>>)

I can see this log when I click the first time, but the log is not printed when I click the second time, I don't know whether it is not reported by the device

The data reported by the device is 0, 1, and 2

PS:
Maybe I shouldn't use the switch type

[xZetsubou]

What if you did double_click then single_click again would it be report both?

[xZetsubou]

Is it even possible to control your device with the integration right now? Because you adding the devices as switch switch only sending true and false your device doesn't accept these values it's accept ["single_click","double_click","long_press"].
It won't be hard to fix we can remap these values but are even sure about this? I can give you better solution if you want.

[xZetsubou]

There are 3 solutions for this:

1. add the device as select. if you said device is 0, 1 and 2 then select config would be like this

2. is to add the device any way you want as sensor or switch but doing action through HA do it with call_service
   to set your actions: [ The best sine you can remap the way you want ]

service: localtuya.set_dp
data:
  device_id: 767823809c9c1f842393 # you devices_id
  dp: 1 # The DP you want to control it
  value: 0 # assuming 0 is single_click

3. Is I can actually make you add button multi times and remap button set_value so you can Have 3 buttons in you HA Device TAB each button perform specific click.

[NJPYY]

Thank you very much.

I think I still don't know much about localtuya, or even HA integration, and I'll spend some time learning it

[xZetsubou]

Were you able to fix it?

[NJPYY]

I think I can, but it takes a little time to understand how it works

[xZetsubou]

by the way what I mean by remap is change the default values of HA commands
for example your switch accept 0, 1 and 2 and HA sends true, false. remap means change true to 0 and false to 1.
my example above I changed dp 1 and remap value to 0