Wifi Dropouts - Would that Cause Issues? #383
Replies: 7 comments 11 replies
-
|
Is it possible that the esp32 is getting hot? |
Beta Was this translation helpful? Give feedback.
-
|
No. It does it as soon as it’s plugged in. That is starts dropping the
WiFi.
…On Mon, Oct 10, 2022 at 6:27 PM Anthony Doud < ***@***.***> wrote:
Is it possible that the esp32 is getting hot? —Reply to this email
directly, view it on GitHub, or unsubscribe.You are receiving this because
you authored the thread.Message ID:
*DuckDuckGo* removed 1 tracker.
More →
<https://duckduckgo.com/-wrQWd6EKAotOs_MJv0mFZGiSlGj5I9CFBr4t1vYkQQFxt-ejk_Zki9oZ7eqZb1VewJ1wa2A5pHPhXZfQRIuEftcTy3U66rI_1RIyoX2fb6sePjCQDzTYId96dAvUIfFM32dTBPzitZytK1L9IiOG9AwtyxBtKnqTaygCmz9mOgfFtlQvdF0DmOAUSehisdCljhQQunLbTwinFkxjgHWRPi1cNDTN04w5nxw6y_t825Z-KeGzYIEtrhE3ucukgZLbPXohUJBZ3xL1e__P4EIFw80yqPS-cRsky_WkC73JNbO8H4>
Is it possible that the esp32 is getting hot?
—
Reply to this email directly, view it on GitHub
<#383 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AQOFTUAGKVVIDM5TFIT6BILWCSJ4FANCNFSM6AAAAAARBT2SJY>
.
You are receiving this because you authored the thread.Message ID:
***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
Barring a hardware issue, the only thing I could think of is if you're trying to use a 5ghz network. Those don't work well/at all. You could also try updating to the latest firmware if you haven't. Edit: It could be doing an automatic upgrade as well. If the blue light is solid or flickering, it's trying to update. That normally takes a couple minutes after boot. |
Beta Was this translation helpful? Give feedback.
-
|
My network is both 2.4 and 5 with the same ssid. I’ll try adding it to my
guest network which is only 2.4.
…On Mon, Oct 10, 2022 at 7:25 PM Anthony Doud < ***@***.***> wrote:
Barring a hardware issue, the only thing I could think of is if you're
trying to use a 5ghz network. Those don't work well/at all. You could also
try updating to the latest firmware if you haven't. —R
*DuckDuckGo* removed 1 tracker.
More →
<https://duckduckgo.com/-wrQWd6EKAotOs_MJv0mFZGiSlGj5I9CFBr4t1vYkQQFxt-ejk_Zki9oZ7eqZb1VewJ1wa2A5pHPhXZfQRIuEftcTy3U66rI_1RIyoX2fb6sePjCQDzTYId96dAvUIfFM32dTBPzitZytK1rVR8lrNYohwK0tKlqnlRQBbZ-TPQPi2yo3mg6hzHAqJNQxWMhSxwoofTlNh4RzqwYxwBrIvxaOOjpGycYcz649Zf2ebcs_FM3YUECW1wi73MXSYMltnr0QqGgM76l6vf_n0CEiwca5VHpfGK2yRdrSJd7EmtneD8>
Barring a hardware issue, the only thing I could think of is if you're
trying to use a 5ghz network. Those don't work well/at all.
You could also try updating to the latest firmware if you haven't.
—
Reply to this email directly, view it on GitHub
<#383 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AQOFTUGLN6ECQK4AXG4XAE3WCSQW5ANCNFSM6AAAAAARBT2SJY>
.
You are receiving this because you authored the thread.Message ID:
***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
Well now I can't even get it to connect to wifi at all - didn't I see somewhere here that there is a way to reset the device completely? I'm wondering if the ESP32 wifi has failed.... @eMadman sent me all the electronics and 3d parts since I didn't have a way to print them. I'm thinking I may just need to build a whole new board - but every time I try to go source parts I find it difficult to determine if I'm getting the correct component (descriptions/specs are slightly different)....is there an updated parts list somewhere with USA links, or someone on here I can just buy all the electronics from their inventory (I also run into minimum order quantity issues) to build 2-3 additional boards? |
Beta Was this translation helpful? Give feedback.
-
|
This is good - it means it's booted up and bluetooth is working. Can you click the "en" button? (to the right of the USB connector when you're looking at the module) and copy/paste the stream of text that shows immediately following that click? It will reboot and initialize wifi - I want to see what the logs show when it's trying to connect to your wifi and whether or not the failsafe "smartspin2k" SSID is being created if a connection could not be established. |
Beta Was this translation helpful? Give feedback.
-
|
Well I probably did things out of your preferred order. I then reset it as @doudar said and becuase I separated my wifi's band's into a separate 2.4 and 5 ghz and stopped it from trying to auto switch. So now it's on the 2.4 ssid... [10:15:28][179753]E: Rebooting f�Request |
Beta Was this translation helpful? Give feedback.
-
|
Sweet! A successful connection to wifi and it looks like the OTA update was also applied Can you reach it at http://192.168.145.153 or http://smartspin2k.local? |
Beta Was this translation helpful? Give feedback.
-
Yes - so far it's been holding a stable connection - as in the page doesn't drop or show unable to be loaded. I'm going to leave the SS2K on today (I normally unplug it) and just randomly refresh the page to see if it's staying connected. All yesterday it was hit or miss or would disconnect as it had a page half loaded. |
Beta Was this translation helpful? Give feedback.
-
I may have spoke too soon - I just hit refresh on the page after typing the above and it was disconnected - although my router's admin page still showed it as connected - I have it set with a static IP as well. I just restarted the SS2k and it reconnected. I'll monitor more. |
Beta Was this translation helpful? Give feedback.
-
|
Wifi is staying connected much better now - only was disconnected once every few hours that I saw...now it wasn't being used at the time either. So a question for the dev's - does it go to sleep or disconnect from wifi after a certain amount of time of inactivity goes by? Otherwise it seems to be staying connected much better than before. |
Beta Was this translation helpful? Give feedback.
-
|
If it's disconnecting after a few hours, I think you're in good shape. I suspect your router may be treating it as an idle device and it's not gracefully returning it to an active state. You can try enabling UDP logging in the settings - this will have it pumping out some data over wifi all the time, but even this will idle out after a while if the device is untouched for a few hours - if nothing's happening, there's nothing to log. I think the recurring "No data found in powertable." from my screenshot below is sufficient since that updates in the log every few seconds. This message will differ if you did a ride and a power table was generated.
|
Beta Was this translation helpful? Give feedback.
-
|
A new automatic update came out a few days ago. Please let me know if that fixed any of your issues. |
Beta Was this translation helpful? Give feedback.
-
For some reason my wifi is not able to hold a signal on the SS2k anymore - even though the access point is less than 5 feet from it. I'm wondering though if the dropping of the wifi would also cause issues with the general use of the SS2k? I'm seemingly having more issues now with the SS2k connecting, but not displaying power, or displaying power but not adjusting resistance....and it seems to be only when I have a wifi issue - a gut feeling that is.
Beta Was this translation helpful? Give feedback.
All reactions