problem booting hi3518ev100

[saurabhchakrabarti]

I'm unable to boot with all the network interfaces for my board (hi3518ev100) after updating with openIPC. Could you please help. Here is the output I'm getting

U-Boot 2010.06-dirty (Jul 10 2021 - 19:39:09)

Check spi flash controller v350... Found
Spi(cs1) ID: 0xC2 0x20 0x17 0xC2 0x20 0x17
Spi(cs1): Block:64KB Chip:8MB Name:"MX25L6406E"
MMC:   MMC FLASH INIT: No card on slot!
In:    serial
Out:   serial
Err:   serial
Detected RAM size: 64Mb
*No SD card found!
USB:   scanning bus for devices... 1 USB Device(s) found
0 Storage Device(s) found
USB:   scanning bus for devices... 1 USB Device(s) found
0 Storage Device(s) found
Hit any key to stop autoboot:  0
8192 KiB hi_sfc at 0:0 is now current device

## Booting kernel from Legacy Image at 82000000 ...
   Image Name:   OpenIPC.org | Linux-3.0.8
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1315464 Bytes = 1.3 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Linux version 3.0.8 (runner@fv-az139-878) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 latest-178-g157e03c47e) ) #1 Sat Jul 10 19:35:39 UTC 2021
[    0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: hi3518
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] AXI bus clock 200000000.
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line: totalmem=64M mem=32M ethaddr=00:12:14:1e:52:fd phyaddru= phyaddrd= sensor=auto linux_cmd=version console=ttyAMA0,115200 panic=20 root=/dev/mtdblock3 rootfstype=squashfs mtdparts=hi_sfc:256k(boot),64k(env),2048k(kernel),5120k(rootfs),-(rootfs_data)
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Memory: 32MB = 32MB total
[    0.000000] Memory: 28956k/28956k available, 3812k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
[    0.000000]     vmalloc : 0xc2800000 - 0xfe000000   ( 952 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc2000000   (  32 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .init : 0xc0008000 - 0xc0024000   ( 112 kB)
[    0.000000]       .text : 0xc0024000 - 0xc0340000   (3184 kB)
[    0.000000]       .data : 0xc0340000 - 0xc0357220   (  93 kB)
[    0.000000]        .bss : 0xc0357244 - 0xc03680f8   (  68 kB)
[    0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:128 nr_irqs:128 128
[    0.000000] sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 42949ms
[    0.000067] Calibrating delay loop... 218.72 BogoMIPS (lpj=1093632)
[    0.070080] pid_max: default: 32768 minimum: 301
[    0.070505] Mount-cache hash table entries: 512
[    0.071712] CPU: Testing write buffer coherency: ok
[    0.076428] NET: Registered protocol family 16
[    0.091386] Serial: AMBA PL011 UART driver
[    0.091724] uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 5) is a PL011 rev2
[    0.307866] console [ttyAMA0] enabled
[    0.312560] uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 5) is a PL011 rev2
[    0.363658] bio: create slab <bio-0> at 0
[    0.385147] SCSI subsystem initialized
[    0.392579] usbcore: registered new interface driver usbfs
[    0.398835] usbcore: registered new interface driver hub
[    0.405246] usbcore: registered new device driver usb
[    0.418245] cfg80211: Calling CRDA to update world regulatory domain
[    0.425407] Switching to clocksource timer1
[    0.438831] NET: Registered protocol family 2
[    0.443579] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.451194] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.458372] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.464899] TCP: Hash tables configured (established 1024 bind 1024)
[    0.471295] TCP reno registered
[    0.474468] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.480456] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.487481] NET: Registered protocol family 1
[    0.492802] RPC: Registered named UNIX socket transport module.
[    0.498746] RPC: Registered udp transport module.
[    0.503542] RPC: Registered tcp transport module.
[    0.508257] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.562744] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.572073] JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.583581] msgmni has been set to 56
[    0.588371] io scheduler noop registered
[    0.592405] io scheduler deadline registered (default)
[    0.597876] io scheduler cfq registered
[    0.635571] brd: module loaded
[    0.643514] Spi id table Version 1.22
[    0.648829] Spi(cs1) ID: 0xC2 0x20 0x17 0xC2 0x20 0x17
[    0.654138] SPI FLASH start_up_mode is 3 Bytes
[    0.658598] Spi(cs1):
[    0.660840] Block:64KB
[    0.663293] Chip:8MB
[    0.665565] Name:"MX25L6406E"
[    0.668718] spi size: 8MB
[    0.671370] chip num: 1
[    0.673869] 5 cmdlinepart partitions found on MTD device hi_sfc
[    0.679796] Creating 5 MTD partitions on "hi_sfc":
[    0.684650] 0x000000000000-0x000000040000 : "boot"
[    0.693803] 0x000000040000-0x000000050000 : "env"
[    0.702790] 0x000000050000-0x000000250000 : "kernel"
[    0.712109] 0x000000250000-0x000000750000 : "rootfs"
[    0.721466] 0x000000750000-0x000000800000 : "rootfs_data"
[    0.750995] Fixed MDIO Bus: probed
[    1.122502] himii: probed
[    1.240100] PHY himii:01 not found
[    1.243528] hieth:hieth_platdev_probe_port:688:
[    1.247975] connect to phy_device himii:01 failed!
[    1.253803] hieth:hieth_plat_driver_probe:817:
[    1.258173] no dev probed!
[    1.261127]
[    1.293058] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.300009] hiusb-ehci hiusb-ehci.0: HIUSB EHCI
[    1.305817] hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
[    1.313864] hiusb-ehci hiusb-ehci.0: irq 15, io mem 0x100b0000
[    1.330124] hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
[    1.338433] hub 1-0:1.0: USB hub found
[    1.342346] hub 1-0:1.0: 1 port detected
[    1.349258] platform rtc-hi3518: rtc core: registered rtc-hi3518 as rtc0
[    1.362612] TCP cubic registered
[    1.365870] NET: Registered protocol family 17
[    1.370744] 802.1Q VLAN Support v1.8
[    1.376834] registered taskstats version 1
[    1.381304] platform rtc-hi3518: setting system clock to 1970-01-01 00:00:00 UTC (0)
▒[    1.394388] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    1.401731] Freeing init memory: 112K
[    2.103500] init: Console is alive
[    3.670666] Initializing USB Mass Storage driver...
[    3.676455] usbcore: registered new interface driver usb-storage
[    3.682563] USB Mass Storage support registered.
[    4.200713] init: - preinit -
get_chip_id35180100() got unexpected 0xffffffff for 3518?v100
Check kernel modules loaded
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
Failed to connect to ubus
Please press Enter to activate this console.
get_chip_id35180100() got unexpected 0xffffffff for 3518?v100


BusyBox v1.23.2 (2021-07-10 19:23:08 UTC) built-in shell (ash)


 ___                  _  ___  ___
/   \ ___  ___  _  _ | ||   \/  _|
| | ||   \/ _ \| \| || || | || |
| | || | |  __/| \\ || ||  _/| |_
\___/|  _/\___||_|\_||_||_|  \___|.ORG    v21.04.10.2
     |_|


OpenIPC is asking for your help to support development cost and long-term maintenance
of what we believe will serve a fundamental role in the advancement of a stable, flexible
and most importantly, Open IP Network Camera Framework for users worldwide.

Your contribution will help us advance development proposals forward, and interact with
the community on a regular basis.

  https://openipc.org/sponsor/



root@OpenIPC:/# Start autoupdate system

root@OpenIPC_HI35xx:/# ifconfig
lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:864 errors:0 dropped:0 overruns:0 frame:0
          TX packets:864 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:70848 (69.1 KiB)  TX bytes:70848 (69.1 KiB)

Here is my ipctool result before I updated it

# ./ipctool
---
board:
  vendor: Xiongmai
  model: HI3518E_50H10L_S39
chip:
  vendor: HiSilicon
  model: 3518EV100
ethernet:
  mac: "00:12:14:1e:52:fd"
  u-mdio-phyaddr: 1
  phy-id: 0x02430c54
  d-mdio-phyaddr: 0
  phy-mode: rmii
rom:
  - type: nor
    block: 64K
    partitions:
      - name: boot
        size: 0x40000
        sha1: efb6ac6b
        contains:
          - name: uboot-env
            offset: 0x30000
      - name: romfs
        size: 0x370000
        path: /,cramfs
        sha1: aba95348
      - name: user
        size: 0x280000
        path: /usr,squashfs
        sha1: ac368e66
      - name: web
        size: 0x140000
        path: /mnt/web,squashfs
        sha1: 7fa09492
      - name: custom
        size: 0x40000
        path: /mnt/custom,squashfs
        sha1: f49d3706
      - name: mtd
        size: 0x50000
        path: /mnt/mtd,jffs2,rw
    size: 8M
    addr-mode: 3-byte
ram:
  total: 64M
  media: 21M
firmware:
  u-boot: "2010.06 (Apr 07 2012 - 17:11:2)"
  kernel: "3.0.8 (Sat Aug 15 16:51:10 CST 2015)"
  toolchain: gcc version 4.4.1 (Hisilicon_v100(gcc4.4-290+uclibc_0.9.32.1+eabi+linuxpthread))
  sdk: "Hi3518_MPP_V1.0.8.0  (Feb 25 2014, 10:55:54)"
  god-app: /usr/bin/Sofia
sensors:
- vendor: Sony
  model: IMX224
  control:
    bus: 0
    type: i2c
    addr: 0x34
  data:
    type: DC
  clock: 24MHz
#