opto7

\mainpage Main Page

---

Opto 7 click

Opto 7 Click is a compact add-on board that provides uncomplicated safety isolation from high voltage. This board features two ISOM8710, high-speed single-channel opto-emulators from Texas Instruments. The ISOM8710 opto-emulator has a diode-emulator input and digital output

click Product page

---

Click library

• Author : Stefan Ilic
• Date : Sep 2023.
• Type : UART/GPIO type

Software Support

We provide a library for the Opto 7 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Library Description

This library contains API for Opto 7 Click driver.

Standard key functions :

• opto7_cfg_setup Config Object Initialization function.

void opto7_cfg_setup ( opto7_cfg_t *cfg );

• opto7_init Initialization function.

err_t opto7_init ( opto7_t *ctx, opto7_cfg_t *cfg );

Example key functions :

• opto7_generic_write Opto 7 data writing function.

err_t opto7_generic_write ( opto7_t *ctx, uint8_t *data_in, uint16_t len );

• opto7_set_gp1_pin Opto 7 set GP1 pin function.

void opto7_set_gp1_pin( opto7_t *ctx, uint8_t pin_state );

• opto7_get_gp2_pin Opto 7 get GP2 pin function.

uint8_t opto7_get_gp2_pin( opto7_t *ctx );

Example Description

This example demonstrates the use of Opto 7 click board by processing the incoming data and displaying them on the USB UART.

The demo application is composed of two sections :

Application Init

Initialization of UART LOG and GPIO pin, and UART drivers.

void application_init ( void ) 
{
    log_cfg_t log_cfg;  /**< Logger config object. */
    opto7_cfg_t opto7_cfg;  /**< Click config object. */

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, " Application Init " );
    
    // Click initialization.
    opto7_cfg_setup( &opto7_cfg );
    OPTO7_MAP_MIKROBUS( opto7_cfg, MIKROBUS_1 );
    
#if ( DEMO_EXAMPLE == EXAMPLE_GPIO )
    opto7_drv_interface_selection( &opto7_cfg, OPTO7_DRV_SEL_GPIO );
#else
    opto7_drv_interface_selection( &opto7_cfg, OPTO7_DRV_SEL_UART );
#endif
    
    if ( UART_ERROR == opto7_init( &opto7, &opto7_cfg ) ) 
    {
        log_error( &logger, " Communication init." );
        for ( ; ; );
    }
    
    log_info( &logger, " Application Task " );
}

Application Task

This example is made of two parts: GPIO Example - The output pin is toggled every 5 seconds and input pin state is being tracked. UART Example - Device assigned as transmitter is sending message and receiver is reading it and displaying it on USB UART.

void application_task ( void ) 
{
#if ( DEMO_EXAMPLE == EXAMPLE_GPIO )
    log_printf( &logger, " GP1 pin state HIGH \r\n" );
    opto7_set_gp1_pin( &opto7, OPTO7_PIN_STATE_HIGH );
     if ( OPTO7_PIN_STATE_HIGH == opto7_get_gp2_pin( &opto7 ) )
    {
        log_printf( &logger, " GP2 pin state HIGH \r\n" );
    }
    else
    {
        log_printf( &logger, " GP2 pin state LOW \r\n" );
    }
    log_printf( &logger, "- - - - - - - - - - - -\r\n" );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    
    log_printf( &logger, " GP1 pin state LOW \r\n" );
    opto7_set_gp1_pin( &opto7, OPTO7_PIN_STATE_LOW );
    if ( OPTO7_PIN_STATE_HIGH == opto7_get_gp2_pin( &opto7 ) )
    {
        log_printf( &logger, " GP2 pin state HIGH \r\n" );
    }
    else
    {
        log_printf( &logger, " GP2 pin state LOW \r\n" );
    }
    log_printf( &logger, "- - - - - - - - - - - -\r\n" );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
#else
#if defined TRANSMITTER
    log_printf( &logger, " Message sent! \r\n" );
    opto7_generic_write( &opto7, TX_MESSAGE, strlen( TX_MESSAGE ) );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
#else
    if ( OPTO7_OK == opto7_process( &opto7 ) ) 
    {
        opto7_log_app_buf( );
        opto7_clear_app_buf( );
    }
#endif

#endif
}

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Other Mikroe Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.Opto7

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.

---