efuse7

\mainpage Main Page

---

eFuse 7 click

eFuse 7 Click is a compact add-on board with a power path protection solution that limits circuit currents and voltages to safe levels during fault conditions. This board features the LS12052BD33, an eFuse with over-voltage protection and blocking FET control from Littelfuse.

click Product page

---

Click library

• Author : Stefan Ilic
• Date : May 2023.
• Type : GPIO type

Software Support

We provide a library for the eFuse 7 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Library Description

This library contains API for eFuse 7 Click driver.

Standard key functions :

• efuse7_cfg_setup Config Object Initialization function.

void efuse7_cfg_setup ( efuse7_cfg_t *cfg );

• efuse7_init Initialization function.

err_t efuse7_init ( efuse7_t *ctx, efuse7_cfg_t *cfg );

• efuse7_default_cfg Click Default Configuration function.

err_t efuse7_default_cfg ( efuse7_t *ctx );

Example key functions :

• efuse7_enable_output eFuse 7 output enable function.

void efuse7_enable_output ( efuse7_t *ctx );

• efuse7_wiper_inc eFuse 7 wiper position increase function.

void efuse7_wiper_inc ( efuse7_t *ctx, uint8_t inc_num );

• efuse7_set_limit eFuse 7 set current limit function.

err_t efuse7_set_limit ( efuse7_t *ctx, uint8_t set_current );

Example Description

This library contains API for the eFuse 7 Click driver. This driver provides the functions to set the current limiting conditions in order to provide the threshold of the fault conditions.

The demo application is composed of two sections :

Application Init

Initialization of click module and UART log, then performing default configuration and setting a current limit to 1A.

void application_init ( void ) 
{
    log_cfg_t log_cfg;  /**< Logger config object. */
    efuse7_cfg_t efuse7_cfg;  /**< Click config object. */

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, " Application Init " );

    // Click initialization.
    efuse7_cfg_setup( &efuse7_cfg );
    EFUSE7_MAP_MIKROBUS( efuse7_cfg, MIKROBUS_1 );
    if ( DIGITAL_OUT_UNSUPPORTED_PIN == efuse7_init( &efuse7, &efuse7_cfg ) ) 
    {
        log_error( &logger, " Communication init." );
        for ( ; ; );
    }
    
    if ( EFUSE7_ERROR == efuse7_default_cfg ( &efuse7 ) )
    {
        log_error( &logger, " Default configuration." );
        for ( ; ; );
    }
    
    log_info( &logger, " Application Task " );
    display_selection( );
    Delay_ms ( 100 );
}

Application Task

This example demonstrates the use of the eFuse 7 Click board. Reading user's input from UART Terminal and using it as an index for an array of pre-calculated values that define the current limit level. Results are being sent to the UART Terminal, where you can track their changes.

void application_task ( void ) 
{
    static char index;
    
    if ( 1 == log_read( &logger, &index, 1 ) ) 
    {
        if ( ( index >= '0' ) && ( index <= '7' ) ) 
        {
            efuse7_set_limit ( &efuse7, limit_value_op[ index - 48 ] );
            log_printf( &logger, "  >>> Selected mode %c     \r\n", index );
            log_printf( &logger, "---------------------------\r\n" );
            Delay_ms ( 100 );
        }
        else 
        { 
            log_printf( &logger, "    Data not in range!    \r\n" );
            log_printf( &logger, "---------------------------\r\n" );
            display_selection( );
            Delay_ms ( 100 );
        }
    }
}

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Other Mikroe Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.eFuse7

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.

---