Skip to content

Latest commit

 

History

History
 
 

threads-intro

Folders and files

NameName
Last commit message
Last commit date

parent directory

..
 
 
 
 
 
 
 
 
 
 
 
 

Overview

Welcome to this simulator! The idea is to gain familiarity with threads by seeing how they interleave; the simulator, x86.py, will help you in gaining this understanding.

The simulator mimicks the execution of short assembly sequences by multiple threads. Note that the OS code that would run (for example, to perform a context switch) is not shown; thus, all you see is the interleaving of the user code.

The assembly code that is run is based on x86, but somewhat simplified. In this instruction set, there are four general-purpose registers (%ax, %bx, %cx, %dx), a program counter (PC), and a small set of instructions which will be enough for our purposes.

Here is an example code snippet that we will be able to run:

.main
mov 2000, %ax   # get the value at the address
add $1, %ax     # increment it
mov %ax, 2000   # store it back
halt

The code is easy to understand. The first instruction, an x86 "mov", simply loads a value from the address specified by 2000 into the register %ax. Addresses, in this subset of x86, can take some of the following forms:

  • 2000 : the number (2000) is the address
  • (%cx) : contents of register (in parentheses) forms the address
  • 1000(%dx) : the number + contents of the register form the address
  • 10(%ax,%bx) : the number + reg1 + reg2 forms the address

To store a value, the same mov instruction is used, but this time with the arguments reversed, e.g.:

mov %ax, 2000

The add instruction, from the sequence above, should be clear: it adds an immediate value (specified by $1) to the register specified in the second argument (i.e., %ax = %ax + 1).

Thus, we now can understand the code sequence above: it loads the value at address 2000, adds 1 to it, and then stores the value back into address 2000.

The fake-ish halt instruction just stops running this thread.

Let's run the simulator and see how this all works! Assume the above code sequence is in the file simple-race.s.

prompt> ./x86.py -p simple-race.s -t 1 

       Thread 0
1000 mov 2000, %ax
1001 add $1, %ax
1002 mov %ax, 2000
1003 halt

prompt> 

The arguments used here specify the program (-p), the number of threads (-t 1), and the interrupt interval, which is how often a scheduler will be woken and run to switch to a different task. Because there is only one thread in this example, this interval does not matter.

The output is easy to read: the simulator prints the program counter (here shown from 1000 to 1003) and the instruction that gets executed. Note that we assume (unrealistically) that all instructions just take up a single byte in memory; in x86, instructions are variable-sized and would take up from one to a small number of bytes.

We can use more detailed tracing to get a better sense of how machine state changes during the execution:

prompt> ./x86.py -p simple-race.s -t 1 -M 2000 -R ax,bx

 2000      ax    bx          Thread 0
    ?       ?     ?
    ?       ?     ?   1000 mov 2000, %ax
    ?       ?     ?   1001 add $1, %ax
    ?       ?     ?   1002 mov %ax, 2000
    ?       ?     ?   1003 halt

Oops! Forgot the -c flag (which actually computes the answers for you).

prompt> ./x86.py -p simple-race.s -t 1 -M 2000 -R ax,bx -c

 2000      ax    bx          Thread 0
    0       0     0
    0       0     0   1000 mov 2000, %ax
    0       1     0   1001 add $1, %ax
    1       1     0   1002 mov %ax, 2000
    1       1     0   1003 halt

By using the -M flag, we can trace memory locations (a comma-separated list lets you trace more than one, e.g., 2000,3000); by using the -R flag we can track the values inside specific registers.

The values on the left show the memory/register contents AFTER the instruction on the right has executed. For example, after the add instruction, you can see that %ax has been incremented to the value 1; after the second mov instruction (at PC=1002), you can see that the memory contents at 2000 are now also incremented.

There are a few more instructions you'll need to know, so let's get to them now. Here is a code snippet of a loop:

.main
.top
sub  $1,%dx
test $0,%dx     
jgte .top         
halt

A few things have been introduced here. First is the test instruction. This instruction takes two arguments and compares them; it then sets implicit "condition codes" (kind of like 1-bit registers) which subsequent instructions can act upon.

In this case, the other new instruction is the jump instruction (in this case, jgte which stands for "jump if greater than or equal to"). This instruction jumps if the second value is greater than or equal to the first in the test.

One last point: to really make this code work, dx must be initialized to 1 or greater.

Thus, we run the program like this:

prompt> ./x86.py -p loop.s -t 1 -a dx=3 -R dx -C -c

   dx   >= >  <= <  != ==        Thread 0
    3   0  0  0  0  0  0
    2   0  0  0  0  0  0  1000 sub  $1,%dx
    2   1  1  0  0  1  0  1001 test $0,%dx
    2   1  1  0  0  1  0  1002 jgte .top
    1   1  1  0  0  1  0  1000 sub  $1,%dx
    1   1  1  0  0  1  0  1001 test $0,%dx
    1   1  1  0  0  1  0  1002 jgte .top
    0   1  1  0  0  1  0  1000 sub  $1,%dx
    0   1  0  1  0  0  1  1001 test $0,%dx
    0   1  0  1  0  0  1  1002 jgte .top
   -1   1  0  1  0  0  1  1000 sub  $1,%dx
   -1   0  0  1  1  1  0  1001 test $0,%dx
   -1   0  0  1  1  1  0  1002 jgte .top
   -1   0  0  1  1  1  0  1003 halt

The -R dx flag traces the value of %dx; the -C flag traces the values of the condition codes that get set by a test instruction. Finally, the -a dx=3 flag sets the %dx register to the value 3 to start with.

As you can see from the trace, the sub instruction slowly lowers the value of %dx. The first few times test is called, only the ">=", ">", and "!=" conditions get set. However, the last test in the trace finds %dx and 0 to be equal, and thus the subsequent jump does NOT take place, and the program finally halts.

Now, finally, we get to a more interesting case, i.e., a race condition with multiple threads. Let's look at the code first:

.main
.top
# critical section
mov 2000, %ax       # get the value at the address
add $1, %ax         # increment it
mov %ax, 2000       # store it back

# see if we're still looping
sub  $1, %bx
test $0, %bx
jgt .top

halt

The code has a critical section which loads the value of a variable (at address 2000), then adds 1 to the value, then stores it back.

The code after just decrements a loop counter (in %bx), tests if it is greater than or equal to zero, and if so, jumps back to the top to the critical section again.

prompt> ./x86.py -p looping-race-nolock.s -t 2 -a bx=1 -M 2000 -c

 2000      bx          Thread 0                Thread 1
    0       1
    0       1   1000 mov 2000, %ax
    0       1   1001 add $1, %ax
    1       1   1002 mov %ax, 2000
    1       0   1003 sub  $1, %bx
    1       0   1004 test $0, %bx
    1       0   1005 jgt .top
    1       0   1006 halt
    1       1   ----- Halt;Switch -----  ----- Halt;Switch -----
    1       1                            1000 mov 2000, %ax
    1       1                            1001 add $1, %ax
    2       1                            1002 mov %ax, 2000
    2       0                            1003 sub  $1, %bx
    2       0                            1004 test $0, %bx
    2       0                            1005 jgt .top
    2       0                            1006 halt

Here you can see each thread ran once, and each updated the shared variable at address 2000 once, thus resulting in a count of two there.

The Halt;Switch line is inserted whenever a thread halts and another thread must be run.

One last example: run the same thing above, but with a smaller interrupt frequency. Here is what that will look like:

prompt> ./x86.py -p looping-race-nolock.s -t 2 -a bx=1 -M 2000 -i 2

 2000          Thread 0                Thread 1
    ?
    ?   1000 mov 2000, %ax
    ?   1001 add $1, %ax
    ?   ------ Interrupt ------  ------ Interrupt ------
    ?                            1000 mov 2000, %ax
    ?                            1001 add $1, %ax
    ?   ------ Interrupt ------  ------ Interrupt ------
    ?   1002 mov %ax, 2000
    ?   1003 sub  $1, %bx
    ?   ------ Interrupt ------  ------ Interrupt ------
    ?                            1002 mov %ax, 2000
    ?                            1003 sub  $1, %bx
    ?   ------ Interrupt ------  ------ Interrupt ------
    ?   1004 test $0, %bx
    ?   1005 jgt .top
    ?   ------ Interrupt ------  ------ Interrupt ------
    ?                            1004 test $0, %bx
    ?                            1005 jgt .top
    ?   ------ Interrupt ------  ------ Interrupt ------
    ?   1006 halt
    ?   ----- Halt;Switch -----  ----- Halt;Switch -----
    ?                            1006 halt

As you can see, each thread is interrupt every 2 instructions, as we specify via the -i 2 flag. What is the value of memory[2000] throughout this run? What should it have been?

Now let's give a little more information on what can be simulated with this program. The full set of registers: %ax, %bx, %cx, %dx, and the PC. In this version, there is no support for a "stack", nor are there call and return instructions.

The full set of instructions simulated are:

mov immediate, register     # moves immediate value to register
mov memory, register        # loads from memory into register
mov register, register      # moves value from one register to other
mov register, memory        # stores register contents in memory
mov immediate, memory       # stores immediate value in memory

add immediate, register     # register  = register  + immediate
add register1, register2    # register2 = register2 + register1
sub immediate, register     # register  = register  - immediate
sub register1, register2    # register2 = register2 - register1

test immediate, register    # compare immediate and register (set condition codes)
test register, immediate    # same but register and immediate
test register, register     # same but register and register

jne                         # jump if test'd values are not equal
je                          #                       ... equal
jlt                         #     ... second is less than first
jlte                        #               ... less than or equal
jgt                         #            ... is greater than
jgte                        #               ... greater than or equal

xchg register, memory       # atomic exchange: 
                            #   put value of register into memory
                            #   return old contents of memory into reg
                            # do both things atomically

nop                         # no op

Notes:

  • 'immediate' is something of the form $number
  • 'memory' is of the form 'number' or '(reg)' or 'number(reg)' or 'number(reg,reg)' (as described above)
  • 'register' is one of %ax, %bx, %cx, %dx

Finally, here are the full set of options to the simulator are available with the -h flag:

Usage: x86.py [options]

Options:
  -h, --help            show this help message and exit
  -s SEED, --seed=SEED  the random seed
  -t NUMTHREADS, --threads=NUMTHREADS
                        number of threads
  -p PROGFILE, --program=PROGFILE
                        source program (in .s)
  -i INTFREQ, --interrupt=INTFREQ
                        interrupt frequency
  -r, --randints        if interrupts are random
  -a ARGV, --argv=ARGV  comma-separated per-thread args (e.g., ax=1,ax=2 sets
                        thread 0 ax reg to 1 and thread 1 ax reg to 2);
                        specify multiple regs per thread via colon-separated
                        list (e.g., ax=1:bx=2,cx=3 sets thread 0 ax and bx and
                        just cx for thread 1)
  -L LOADADDR, --loadaddr=LOADADDR
                        address where to load code
  -m MEMSIZE, --memsize=MEMSIZE
                        size of address space (KB)
  -M MEMTRACE, --memtrace=MEMTRACE
                        comma-separated list of addrs to trace (e.g.,
                        20000,20001)
  -R REGTRACE, --regtrace=REGTRACE
                        comma-separated list of regs to trace (e.g.,
                        ax,bx,cx,dx)
  -C, --cctrace         should we trace condition codes
  -S, --printstats      print some extra stats
  -c, --compute         compute answers for me

Most are obvious. Usage of -r turns on a random interrupter (from 1 to intfreq as specified by -i), which can make for more fun during homework problems.

  • -L specifies where in the address space to load the code.
  • -m specified the size of the address space (in KB).
  • -S prints some extra stats
  • -c is not really used (unlike most simulators in the book); use the tracing or condition codes.

Now you have the basics in place; read the questions at the end of the chapter to study this race condition and related issues in more depth.